VDIAGTOOL V200 Power Probe Short Finder 12V 24V Automotive Circuit Probe Tester

Description: VDIAGTOOL V200 Power Probe Short Finder 12V 24V Automotive Circuit Probe Tester【More Easier Electrical Troubleshooting】 - This circuit probe tester is a simple but extremely useful electronic tool to check whether your car's circuits or a certain component is energized or not. This power circuit probe can perform Voltage & Polarity Testing, Continuity Testing, Signal Circuit Testing, Activating Components and Testing Trailer Lights and Connections to reduce the diagnosis time in all electrical systems of 12-24V vehicles.【4 Working Modes】 - This power circuit probe tester supports 4 working modes: DC voltage (Resolution 0.1V), AC voltage, Resistance and Diode, which can tell you instantly whether the wire or circuit is live and which side of the circuit you are on, positive or negative. Save you thousands in finding shorts in main wire harnesses. It is powered by vehicle’s battery or cigarette lighter, no extra battery needed.【Component Activation】 - The activation test function is designed to generate activation signals to the tested components. Such as car lights, motors, windshield wipers, radiator fans, relay, fuel injector and other on-board electric equipments to troubleshoot the electrical problems. You can also use this tool to locate short circuits in your car if you keep getting blown fuses.【Sensor/Signal Circuit Test】 - Troubleshoot the errors when extracting DTCs from vehicles. Using alternating voltage mode, you can test sensors, signal circuits and test the resistance of various sensors and issues, then compare those values to the factory specifications.【Overload Protection】 - This circuit probe kit is built-in short circuit protection. It is got automatic circuit breaker, and whenever it gets overloaded, it just gonna shut down and restart, which is a safe measure to protect the device and your components from overload.【20ft Extension Cord】 - Allows you to reach from front to rear of the vehicle, test the entire electrical circuit system easily. There is also cable with alligator clip for exhilarate ground connection. This allow you to test resistance on the components outside of the vehicle.VDIAGTOOL V200 Car Circuit Probe Tester is an electrical troubleshooting time-saver >>>If there is trouble without an obvious cause in any electrical component, test the circuit to find the cause. >>>But the electrical wiring in a car contains many interlinking and branching circuits, which bring complications. >>>What can this automotive electric circuit tester do for you?It is a more handy, useful and inexpensive tool for making electrical tests.Find shortcuts which save you a lot of time other than checking an entire circuit.Circuit testers diagnose and troubleshoot breaks in automotive electrical connections. >>>Product Features:DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz.4 working modes: DC voltage, AC voltage, Resistance and Diode Test.Identify voltage and polarity of the circuit. You can find out whether it is a positive or negative ground circuit and check how many volts is getting.You can test continuity of the wires and components, whether they are attached to or disconnected from the vehicle.Test the resistance of various sensors and issues and compare those values to the factory specifications.Activate and test components in your hands or inside the vehicle by supplying positive or negative circuits to them.20FT extension cable allows you to work on semi trucks, trailers or any other long vehicles.Built-in light enables better working in darker spaces.4 Working Modes - Simply Switch The Mode Button >>> ✔️ DC Voltage Test:DC voltage detects the voltage value of the circuit under test with a resolution of 0.1 volt. >>> ✔️ AC Voltage Test:AC voltage detects the Max. Voltage, the Min. Voltage and Frequency of the circuit under test. >>> ✔️ Resistance Test:Detect the resistance between the circuit probe tip and auxiliary ground lead.Determines whether an electrical circuit is complete or broken and if the resistance of a component matches the manufacturer's specification. >>> ✔️ Diode Test:Detect the operation of the diode assembly and determine if it is conducting.Display the actual forward voltage of the diode when its conducting current. >>>WARNING:Applying voltage to some circuits at will damage the electronic components of the vehicle.Kindly use the vehicle manufacturer's schematics and diagnostic procedures when testing. >>>NOTE:When power up this probe tester kit, press the power switch first, then contact the tip with the component, the operation life of power switch will be extended.This Automotive Power Probe Tester Can Do More Than A Multi meter >>> ✔️ Locate The Short Circuit:In most cases a short circuit wil appear by a blown fuse or an electrical protection device tripping (i.e., a circuit breaker). Use the probe tip to activate and energize each of the fuse contacts. The contact which trips the circuit breaker is the shorted circuit. >>> ✔️ Check Continuity:When this auto circuit tester is in Resistance mode, using the probe tip and the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehide's electrical system. >>> ✔️ Activate Components:Activate and test components in your hands or inside the vehicle by supplying positive or negative circuits to them. Such as car lights, motors, windshield wipers, radiator fans, relay, fuel injector and other on-board electric equipments. >>> ✔️ Test Trailer Lights:When this circuit probe kit is in DC Voltage mode, clip the auxiliary ground lead to the trailerground, probe the contacts at the jack and then apply voltage to the probe tip. This allows you check the function and orientation of the connector and trailer lights. >>> ✔️ Find The Bad Ground:Probe the suspected ground wire or contact with the probe tip. If the circuit breaker tripped, this circuit is more than likely a good ground.Generate Activation Signals to the Tested Components >>>The activation test function is designed to generate activation signals to the tested components. Such as car lights, relay, fuel injector, motors and other on-board electric equipments. >>> ✔️ Activate Components in Your HandWhen this power probe tester is in DC voltage mode, contact the probe tip with the auxiliary ground lead, the components will be activated in your hand, and test their functions.Steps to active the bulb:Press the power switch forward to activate the bulb.Contact the tip to the positive terminal of the bulb.Connect the negative auxiliary clip. >>> ✔️ Activate Components in The VehicleWhen this electric circuit tester is in DC Voltage mode, contact the probe tip to the positive terminal of the component, the green LED should light up, indicating continuity with the ground.If the green LED went off at that instant or if the circuit breaker tripped, the tool has been overloaded. If the circuit breaker is tripped, wait for 15 seconds to reset the circuit breaker. >>> This could happen for the following reasons:What you are detecting is a direct ground.The component you are testing is short-circuited.The component is a very high current component (i.e., starter motor).Troubleshoot the Errors When Extracting DTCs From Vehicles >>>Once the diagnostic trouble code (DTC) is extracted from the vehicle and you realize that troubleshooting starts with a sensor circuit, you can perform a quick test to verify the code. >>>Using alternating voltage mode, you can test sensors and signal circuits. >>>Do you suspect that there is something wrong with your sensor?Go to AC voltage mode and use the probe tip with auxiliary grounding lead.Contact the probe tip with the positive terminal of sensor.LCD reading shall be a sine wave under normal conditions.If the LCD reading is abnormal, the sensor is faulty Quick Self-test Quick self test to make sure it is working properly before you start using it.Press the power switch forward to activate the tip with a positive voltage. The red LED lights up and display the battery voltage.Press the power switch backwards to activate the tip with a negative voltage, the green LED should light up and the display will read 0.0V. Built-in Light When you power up the circuit probe tester, the 2 led lights on top of it will automatically turn on.This could be a very useful feature when working in darker spaces such a fuse box under the steering wheel, for example, without having to use a flashlight. 2 Charging Modes This power probe circuit can be powered by the car's battery or cigarette lighter, no extra battery or cable required. PaymentDelivery detailsTerms of salesAbout usContact usPayment 1.We accept Credit cards、Debit card、Apple Pay、Google Pay、PayPal ect. payment. 2.Please contact us if you need to use another method to pay. 3.Payment should be made within 30 days after bidding ends. 4.Otherwise an Unpaid Item case will be opened to you. 5.We are not responsible for buyers’ local taxes. 6.Please include your special requests in eBay note if there is any. 7.We reserve the final right of sellingDelivery details Shipping: Order will be shipped within 1-3 business day after payment confirmed. We have warehouse in USA，UK，Australia and China warehouse. From our US/UK/AU warehouse via UPS or DHL eCommerce shipping. Delivery time varies from 2 to 6 business days. From our Hong Kong warehouse via DHL or FedEx Ground Delivery time varies from 3 to 10 business days. From our China warehouse For US Buyers, we use SpeedPAK (Delivery time is 7-25 business days) or express delivery(Delivery time is 3-10 business days) . For other countries' buyers, we use SpeedPAK / China Post (Delivery time varies from 10 to 30 business days)or Express delivery(Delivery time is 3-10 business days). We will ship according to your eBay or PayPal address. Please make sure it is correct and include phone number for delivery. If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem. Please include your special requests in eBay note if there is any. We will try our best to give customers good and pleasant parchasing experience. Welcome your any-time order :)Terms of sales We are Professional Diagnostic Equipment Dealer Store, our all items are 100% original and Our devices have warranty. 12 months free repair for the devices. 3 months for the accessories. Please contact us firstly when you need warranty service. In case an item arrives faulty, please contact us in 30 days and keep it unused. You must tell us what the defect is and give us your eBay ID. We will instruct you on how to return and get refund or replacement. If after 30 days, or the item has been used, we have the right to decline your claim. Items should be returned on buyers' cost for repair or replacement. Terms of tax: We are not responsible for buyer's local taxes, please consult your local Customs for tax details.About us Who We Are? We are specialized dealer of On-Board Diagnostic tools and automotive electronics For more than 10 years. We are authorized first class distributor of XTOOL, VXDIAG, VDIAGTOOL, Xhorse, XTUNER brands. and more brands will be show in our store in near future. If you like our products, please add our eBay shop to your "My Favorites" list. What Do We Have? We have office and warehouse in Australia and US to ensure fast shipment and after-sale service. We have more than 60 employees devoting to customer satisfaction. We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. Please let us know the problem BEFORE you give us or feedback, so that we can satisfactorily address your concerns.Contact us Our customer-oriented service strives for positive feedbacks with all 5 star selling ratings. Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case. We will reply in 24 business hours. Business time: GMT8 (9:00-18:00) from Monday to Friday.

Price: 124.99 AUD

Location: Shen Zhen

End Time: 2024-03-23T10:31:01.000Z

Shipping Cost: 0 AUD