ScaleTrains Rivet Counter HO Penn Central SD45 PC #6146

Description: This listing is for a NEW ScaleTrains HO scale Penn Central EMD SD45 locomotive (PC #6146) w/ ESU LokSound DCC & sound. *Some stock photos may show different road number Road Number Specific ScaleTrains Era: early 1970s to mid 1970sPhase Ib1Road number 6146Series 6141 to 6166 (ex-PRR), built 01/67Late (2-strap) cab signal cabinet on top of battery box, engineer’s sideLost-wax Leslie RS-3L-R horn mounted center rear of number board housingFully-assembledMultiple road numbersOperating LED, red-only marker lights**Operating LED ground lights on both sides of locomotivePrinted and LED-lighted number boardsFront and rear full-width MU hose catch trays without footboards“Short” stepwells with see-through steps“Early” (“X”) pattern walkway treadplateFront and rear early small deck extensionPivoting front and rear drop stepsRectangular walkway lights (non-operating)Latched battery box doors with narrow louversCab sub-base doors with stiffener rib81” low short hood with plated-over handbrake locationStandard EMD high headlight in numberboard housingEarly straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top; top and side grabs relocated to left side to clear cab signal cabinet“35-Line” cab with standard front windshieldsDetailed cab interior with separate floor, rear wall, seats, and standard AAR control standNo cab ventsSliding cab windowsTall square corner clear wind wings with mirrors at the bottom mounted fore of cab side window on both sides of cabNo sunshadesNo arm restsLarge Sinclair Excalibur “ice skate” antenna (communications) mounted on cab roofAccurate hood door and long hood detailsStandard electrical cabinet seam and bolted alternator doorNo ECAFBEarly (smooth) blower duct housingInertial air intake grilles without drip railsStandard-height dust binStandard-height exhaust stackEarly (short forward taper) extended-range dynamic brakesAccurately profiled dynamic brake housingSee-through dynamic brake intakes with resistor grid“Chickenwire” radiator intake grilles with diamond-pattern mesh screensStandard-height fan housingsPhotoetched spiral-ring fan grilles with center diskLong walkway duct with three short stanchionsSemi-scale coupler buffer equipped with durable metal semi-scale Type “E” knuckle couplersFront and rear straight uncoupling levers with four bracketsHandrail set with pilot face mounted outer end rail stanchions4-hose MU hose clusters with silver gladhandsDual early (angled) deck-mounted MU receptaclesShort “nub-bottom” pilot facePilot face bracing detail behind stepwellsPilot face grab iron with inner mounting pointsUnderbody frame rail with separate plumbing and traction motor cablesTall jacking pads with holesSill-mount EFCO buttonFrame-mounted steel bellSalem air filter (accordion style)4,000-gallon fuel tank with single fuel filler, single vertical fuel gauge, and round dial fuel gauge per sideDetailed Flexicoil-C (high-mount brake cylinder) trucks with Hyatt bearing caps and sanding lines and bracketsSpeed recorder second axle, right sideACI labels attached to long hood sidesFactory-applied detail parts: wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and much moreMotor with 5-pole skew-wound armatureDual flywheelsAll-wheel driveAll-wheel electrical pick-upDirectional LED headlightsPrinting and lettering legible even under magnificationOperates on Code 70, 83 and 100 railPackaging safely stores modelMinimum radius: 18”Recommended radius: 22”DCC & sound equipped locomotives also feature:ESU LokSound 5 DCC & Sound decoder with “Full Throttle” featureDual cube-type speakersEMD 20-Cylinder 645E3 turbocharged prime mover soundsESU designed “PowerPack” with two super capacitors***Operates on both DC and DCC layouts

Price: 295 USD

Location: New Bedford, Massachusetts

End Time: 2024-09-16T23:08:21.000Z

Shipping Cost: N/A USD