RIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER

Description: High QualityFast ShippingCustomer SupportRIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK RIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK acquired at woodworking shop that closed their doorsfree shipping with FEDEX ground Application: • Single Acting, Handed • Exterior or Interior Doors • Weight to 450 lbs.* • Door Width up to 4'0" (1219mm) Product Description & Features: • Maximum opening 180, auxiliary floor or wall stop recommended • Separate and independent valves for closing speed and latch speed • Adjustable hydraulic backcheck • Available non-hold open (NHO) • Not available with delayed action (DA) • Models available to meet ICC/ANSI A117.1 low opening force requirements, prefix PH. (For 8-1/2 lbs. of opening force prefix PH and suffix 8-1/2 lbs.) • Available 1-1/2" offset, for doors with 3/4" cladding or frames with applied molding, maximum door weight 250 lbs. • Uses Cycolac, rustproof cement case (order separately - 253001) • Vertical door adjustment • For arch top doors or applications where a 180 top pivot cannot be used, supply at least two each M190 load-bearing intermediate pivots, mounted together at the top of the vertical edge • Intermediate pivot(s) required: M19 (order separately) • Doors 60" (1524mm) to 90" (2286mm) in height should use one intermediate pivot. Each additional 30" (762mm) warrants another intermediate pivot • For fire rated openings (up to 3 hour assemblies) prefix F. This package will be supplied with a steel top pivot (F180) and a non-hold open closer. Intermediate pivot required: FM19 (order separately) • UL labeled closers cannot have PH option • For 20-minute labeled doors suffix "-20" to the part number • Furnished with wood and machine screws • Extended spindles available in 1/2" increments up to 2" longer than standard • * Door size & weight guidelines are determined using the appropriate number of intermediate pivots {Degree of Opening} • Floor closers may have a stop or limitation on the degrees of swing that a door will open. The purpose of this stop is to prevent the door from hitting a wall or other architectural feature. • Typical swings are at 90 or 105 or 180 degrees. • Door hardware may require that a door swing to only 85 degrees to prevent exterior handles from hitting a wall. Similarly, hardware on the push side of the door may require that the door swing further than 90 degrees to clear the opening of protruding hardware. • For closers that do not have a dead stop, you may need to utilize an overhead holder/stop to prevent a door from swinging past the required stop point. BUY NOW!PaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: VISA - MASTERCARD - PAYPAL - AMEX - DISCOVERY - G-PAY Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. We do not ship on weekends and holidays. - When your shipping label is generated a notification will be sent via your email. Tracking number will be included. - International buyers must allow 4-6 weeks for delivery. If still not received by then, please contact us. Delays are often due to the customs process in your country. Import duties, tariffs, and taxes are not included. These charges are the buyers responsibility. Please take a look carefully at the pictures and item description. We will accept ALL returns, but if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preference, we will apply a 15% restocking fee from the original price of purchase. Buyer will pay for shipping, if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preference Please take a look carefully at the pictures and item description. We will accept ALL returns, but if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preference, we will apply a 15% restocking fee from the original price of purchase. The buyer will pay for the return shipping if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn’t your preferenceHigh QualityFast ShippingCustomer SupportRIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK ---acquired at woodworking shop that closed their doors ---free shipping with FEDEX ground Application: • Single Acting, Handed • Exterior or Interior Doors • Weight to 450 lbs.* • Door Width up to 4'0" (1219mm) Product Description & Features: • Maximum opening 180, auxiliary floor or wall stop recommended • Separate and independent valves for closing speed and latch speed • Adjustable hydraulic backcheck • Available non-hold open (NHO) • Not available with delayed action (DA) • Models available to meet ICC/ANSI A117.1 low opening force requirements, prefix PH. (For 8-1/2 lbs. of opening force prefix PH and suffix 8-1/2 lbs.) • Available 1-1/2" offset, for doors with 3/4" cladding or frames with applied molding, maximum door weight 250 lbs. • Uses Cycolac, rustproof cement case (order separately - 253001) • Vertical door adjustment • For arch top doors or applications where a 180 top pivot cannot be used, supply at least two each M190 load-bearing intermediate pivots, mounted together at the top of the vertical edge • Intermediate pivot(s) required: M19 (order separately) • Doors 60" (1524mm) to 90" (2286mm) in height should use one intermediate pivot. Each additional 30" (762mm) warrants another intermediate pivot • For fire rated openings (up to 3 hour assemblies) prefix F. This package will be supplied with a steel top pivot (F180) and a non-hold open closer. Intermediate pivot required: FM19 (order separately) • UL labeled closers cannot have PH option • For 20-minute labeled doors suffix "-20" to the part number • Furnished with wood and machine screws • Extended spindles available in 1/2" increments up to 2" longer than standard • * Door size & weight guidelines are determined using the appropriate number of intermediate pivots {Degree of Opening} • Floor closers may have a stop or limitation on the degrees of swing that a door will open. The purpose of this stop is to prevent the door from hitting a wall or other architectural feature. • Typical swings are at 90 or 105 or 180 degrees. • Door hardware may require that a door swing to only 85 degrees to prevent exterior handles from hitting a wall. Similarly, hardware on the push side of the door may require that the door swing further than 90 degrees to clear the opening of protruding hardware. • For closers that do not have a dead stop, you may need to utilize an overhead holder/stop to prevent a door from swinging past the required stop point. RIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK RIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK acquired at woodworking shop that closed their doorsfree shipping with FEDEX ground Application: • Single Acting, Handed • Exterior or Interior Doors • Weight to 450 lbs.* • Door Width up to 4'0" (1219mm) Product Description & Features: • Maximum opening 180, auxiliary floor or wall stop recommended • Separate and independent valves for closing speed and latch speed • Adjustable hydraulic backcheck • Available non-hold open (NHO) • Not available with delayed action (DA) • Models available to meet ICC/ANSI A117.1 low opening force requirements, prefix PH. (For 8-1/2 lbs. of opening force prefix PH and suffix 8-1/2 lbs.) • Available 1-1/2" offset, for doors with 3/4" cladding or frames with applied molding, maximum door weight 250 lbs. • Uses Cycolac, rustproof cement case (order separately - 253001) • Vertical door adjustment • For arch top doors or applications where a 180 top pivot cannot be used, supply at least two each M190 load-bearing intermediate pivots, mounted together at the top of the vertical edge • Intermediate pivot(s) required: M19 (order separately) • Doors 60" (1524mm) to 90" (2286mm) in height should use one intermediate pivot. Each additional 30" (762mm) warrants another intermediate pivot • For fire rated openings (up to 3 hour assemblies) prefix F. This package will be supplied with a steel top pivot (F180) and a non-hold open closer. Intermediate pivot required: FM19 (order separately) • UL labeled closers cannot have PH option • For 20-minute labeled doors suffix "-20" to the part number • Furnished with wood and machine screws • Extended spindles available in 1/2" increments up to 2" longer than standard • * Door size & weight guidelines are determined using the appropriate number of intermediate pivots {Degree of Opening} • Floor closers may have a stop or limitation on the degrees of swing that a door will open. The purpose of this stop is to prevent the door from hitting a wall or other architectural feature. • Typical swings are at 90 or 105 or 180 degrees. • Door hardware may require that a door swing to only 85 degrees to prevent exterior handles from hitting a wall. Similarly, hardware on the push side of the door may require that the door swing further than 90 degrees to clear the opening of protruding hardware. • For closers that do not have a dead stop, you may need to utilize an overhead holder/stop to prevent a door from swinging past the required stop point. BUY NOW!Payment We accept payment by any of the following methods: VISA - MASTERCARD - PAYPAL - AMEX - DISCOVERY - G-PAY Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!Shipping Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. We do not ship on weekends and holidays. - When your shipping label is generated a notification will be sent via your email. Tracking number will be included. - International buyers must allow 4-6 weeks for delivery. If still not received by then, please contact us. Delays are often due to the customs process in your country. Import duties, tariffs, and taxes are not included. These charges are the buyers responsibility. Please take a look carefully at the pictures and item description. We will accept ALL returns, but if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preference, we will apply a 15% restocking fee from the original price of purchase. Buyer will pay for shipping, if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preferenceReturns Please take a look carefully at the pictures and item description. We will accept ALL returns, but if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn't your preference, we will apply a 15% restocking fee from the original price of purchase. The buyer will pay for the return shipping if the return is because you no longer want the product, changed your mind, ordered the wrong item, or because it isn’t your preferenceHigh QualityFast ShippingCustomer Support RIXSON 27 SERIES 3/4" OFFSET FLOOR CLOSER - LAP RIXSON-FIREMARK acquired at woodworking shop that closed their doorsfree shipping with FEDEX ground Application: • Single Acting, Handed • Exterior or Interior Doors • Weight to 450 lbs.* • Door Width up to 4'0" (1219mm) Product Description & Features: • Maximum opening 180, auxiliary floor or wall stop recommended • Separate and independent valves for closing speed and latch speed • Adjustable hydraulic backcheck • Available non-hold open (NHO) • Not available with delayed action (DA) • Models available to meet ICC/ANSI A117.1 low opening force requirements, prefix PH. (For 8-1/2 lbs. of opening force prefix PH and suffix 8-1/2 lbs.) • Available 1-1/2" offset, for doors with 3/4" cladding or frames with applied molding, maximum door weight 250 lbs. • Uses Cycolac, rustproof cement case (order separately - 253001) • Vertical door adjustment • For arch top doors or applications where a 180 top pivot cannot be used, supply at least two each M190 load-bearing intermediate pivots, mounted together at the top of the vertical edge • Intermediate pivot(s) required: M19 (order separately) • Doors 60" (1524mm) to 90" (2286mm) in height should use one intermediate pivot. Each additional 30" (762mm) warrants another intermediate pivot • For fire rated openings (up to 3 hour assemblies) prefix F. This package will be supplied with a steel top pivot (F180) and a non-hold open closer. Intermediate pivot required: FM19 (order separately) • UL labeled closers cannot have PH option • For 20-minute labeled doors suffix "-20" to the part number • Furnished with wood and machine screws • Extended spindles available in 1/2" increments up to 2" longer than standard • * Door size & weight guidelines are determined using the appropriate number of intermediate pivots {Degree of Opening} • Floor closers may have a stop or limitation on the degrees of swing that a door will open. The purpose of this stop is to prevent the door from hitting a wall or other architectural feature. • Typical swings are at 90 or 105 or 180 degrees. • Door hardware may require that a door swing to only 85 degrees to prevent exterior handles from hitting a wall. Similarly, hardware on the push side of the door may require that the door swing further than 90 degrees to clear the opening of protruding hardware. • For closers that do not have a dead stop, you may need to utilize an overhead holder/stop to prevent a door from swinging past the required stop point.

Price: 399.99 USD

Location: Oceanside, California

End Time: 2024-09-12T18:35:13.000Z

Shipping Cost: 0 USD