Description: This listing is for a kit of electronic parts necessary for the premium restoration of your Pioneer SX-1010. The pictures are meant to show where these parts go and how it all should look. The units in the pictures are examples and are not for sale. Note: If your unit is in need of this level of service, and you do not wish to tackle it and have nobody to do it for you, you can send it to me for service. The first step would be to run a diagnostic to pin down the exact condition and needs of the piece. I shall be pleased to help you with it. For more information, check this listing: Vintage Audio Components-----Repair Service-----Bench Check and Report Be sure to check out my other listings at my eBay store: LION AUDIO TEXAS. International Orders Welcome! I have serviced the Pioneer SX-1010 since they first came out. I see them frequently now for restoration work so I know exactly what they need at this time in their lives. Service needs change over time. When a lovely piece like this gets to forty years old, it needs some general help. Most of the SX-1010’s that come in for service are not outright blown up. They frequently work…..somewhat. They are, however, full of old capacitors, noisy signal path transistors, heat fatigued voltage regulators, and bad relays. Of course, they are in dire need of cleaning and alignment. This sort of job can be undertaken by a qualified technician or a serious hobbyist. Of course it helps to have the precise parts needed in hand, along with their precise locations. This kit is meant to supply that need. It is not a “paint by number” for those with no experience, but with moderate test equipment and some technical skill and patience, good results can be had. Recommended Test Equipment: Multimeter, Variac (5 amp or greater) These can be had right here on eBay and they are not expensive. An oscilloscope is useful if you need to trace lost signals. They are rarely needed for this service. The service manual is invaluable and may be had on line. Try HiFi engine. The kit includes the standard and usual parts required on the following boards. The parts will be in individual bags for each board. There will be a list of parts for each of these boards with schematic designation. There will be a procedural tip sheet. You will find the tip sheet to be very useful as it will contain a lot of information derived from the service experience on this model for forty years. This kit is not guaranteed to solve any and all problems. If your unit has an outright defect, it may be something other than the standard and usual. Great care should be taken to get polarities and transistor basing correct. Careful and tidy workmanship pays off. Be prepared to trouble shoot if you make a mistake or have additional problems. AWF-013-0. Equalizer Amplifier Assembly AWG-027-0. Control Amplifier Assembly AWH-032-0. Power Amplifier Assembly AWM-062-0. Protection Circuit Assembly AWR-054-A. Power Supply Circuit Assembly ACH-054-A. Power Supply Filter Capacitors (2) The capacitors in the kit will vary but will be selected from the following: Power supply applications will be mainly Nichicon VZ and PW. On the other boards, they will be Nichicon FG, KW, FW, KT, VZ or Elna Cerafine or Silmic II. The semiconductors in the kit will be well vetted substitutes for the original Japanese numbers. I have been using all of these parts for quite some time, and they perform very well. The kit does not contain lamps as some folks want incandescent and others want LED so lamps should be purchased separately. The kit does not contain tuner section parts as tuner work should only be attempted by tuner experts. The kit does contain the power supply filter capacitors. When all of these parts are replaced, and the unit is cleaned up and alignments are done, reliability is enhanced, and the sonic quality is astounding. They knew how to do stereo back in the old days. So you have this very excellent piece of equipment. You are well aware that since it is quite old it needs serious attention. You are stuck though. You don’t really want to ship it to someone who is an expert in dealing with this specific model, but you don’t really want your local tech to do it either. After all, he might be a good fellow and a decent tech, but he just doesn’t know this model and you just don’t trust that he will get to the bottom of it. This means that this parts kit is just what you need. You can present your tech with the precise parts that must be replaced. That will certainly help. What is more important though is the instruction sheet. The instruction sheet starts with general procedural instructions, then goes on to discuss each of the PC boards. What to do….what to watch out for….how to be sure that it is done correctly, that it performs like it hasn’t in years, and that it is stable, it will perform well for years. What could be better? With this kit, and with a patient and reasonably competent installer, you can get the kind of results you would not have thought possible.
Price: 209.95 USD
Location: Dripping Springs, Texas
End Time: 2024-09-21T01:03:47.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Pioneer
