Harley Davidson electrical accessory connection splitter 6 way six pin connector

Description: This harness is designed to provide battery power, ignition/accessory power, and ground connection from the six-way Digital Technician connector [91A]The power from this Electrical Connection Harness is fused at 15 amps through the vehicle harness. Fits 2014 on XL, 2012 on Dyna and 2011 on Softail models. Dyna Fat Bob - FXDF 2012-2017Dyna Low Rider - FXDL 2014-2017Dyna Street Bob - FXDB 2012-2017Dyna Super Glide Custom - FXDC 2012-2014Dyna Wide Glide - FXDWG 2012-2017Low Rider S - FXDLS 2016-2017Softail Slim - FLS 2012-2017Sportster 1200 Iron - XL 1200NS 2018-2020Sportster Custom - XL 1200C 2014-2019Sportster Forty-Eight - XL 1200X 2014-2020Sportster Forty-Eight Special - XL 1200XS 2018-2019Sportster Iron - XL 883N 2014-2020Sportster Roadster - XL 1200CX 2016-2020Sportster Seventy Two - XL 1200V 2014-2016Sportster Superlow - XL 1200T 2014-2017Sportster SuperLow - XL 883L 2014-2019 Follow the original manufacturer's instructions !!! WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)Refer to the service manual and follow the instructions to remove the main fuse.Remove the seat per service manual instructions.Locate the Digital Technician connector [91A] (a gray six-way Deutsch pin connector with a rubber boot) under the seat. Place the Electrical Connection Harness at the Digital Technician connector, but DO NOT connect them at this time.Route the wires of the accessory (or accessories) to be connected over to the Electrical Connection Harness per the instructions in the accessory kit (or kits). Cut the wires of the accessory (or accessories) to a suitable length to easily reach the sealed splice connectors (8) on the Electrical Connection Harness.The Electrical Connection Harness serves as a convenient connection point for accessory wires that would otherwise need to be connected to the vehicle fuse block or B+ connector.Splicing of wire leads is necessary in the installation of many accessories to the motorcycle. Refer to the service manual appendix for proper wire splicing procedures.Up to two #16AWG wires can be connected at each sealed splice connector. If more than two #16AWG wires or one #14AWG wire needs to be connected, additional Electrical Connection Harnesses will be required.The accessory wire (or wires, typically orange with a white stripe) that would otherwise connect to the fuse block should be spliced to the yellow (ignition/accessory power) wires in the Electrical Connection Harness.The accessory wire (or wires, typically red) that would otherwise connect to the B+ connector should be spliced to the red (battery power) wires in the Electrical Connection Harness.The accessory ground wire (or wires, typically black) should be spliced to the black (ground) wires in the Electrical Connection Harness. If ring terminals are provided in the kit, they can be used instead to connect directly to the vehicle ground.WARNINGBe sure to follow manufacturer's instructions when using the UltraTorch UT-100 or any other radiant heating device. Failure to follow manufacturer's instructions can cause a fire, which could result in death or serious injury. (00335a)Avoid directing heat toward any fuel system component. Extreme heat can cause fuel ignition/explosion resulting in death or serious injury.Avoid directing heat toward any electrical system component other than the connectors on which heat shrink work is being performed.Always keep hands away from tool tip area and heat shrink attachment.Use a heat gun or suitable radiant-heating device to shrink the connector to the wires. Seal any unused connections to protect against corrosion.INSTALLATION1.Pull the rubber boot out from the gray Digital Technician pin connector [91A].2.Connect the socket housing of the Electrical Connection Harness to connector [91A].3.Install the rubber boot into the pin connector of the Electrical Connection Harness.NOTEVerify that the ignition key switch is in the OFF position before installing the main fuse.4.Refer to the service manual and follow the instructions to install the main fuse.5.Test the accessory or accessories for proper operation.WARNINGAfter installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b)6.Install the seat per service manual instructions.

Price: 24.99 USD

Location: Samokov

End Time: 2024-12-22T06:14:50.000Z

Shipping Cost: 11.99 USD