Description: Product DescriptionThe FMTIA8 is the new turbo inlet adaptor for the Toyota Yaris GR. Throughout the development process we have strived to improve the efficiency and performance of the Yaris GR’s engine and for this product we felt we would offer the whole inlet pipe work as one complete package. FMTIA8 consists of a billet machined turbo adaptor, two 5 ply silicone hoses and mandrel bent alloy hard pipe.Each of these components have been designed to provide the turbo with a smooth and free flowing path thus creating the highest possible flow rate. When you compare FMTIA8 to the OEM pipe work it is clear to see all the restrictions from the OEM configuration have been removed, especially at the critical area where the inlet tract meets the turbo increasing the size from 48mm to 63mm diameter. We have also eliminated the ribbed areas and noise chambers with the goal to create the smoothest possible air flow to the turbo.It’s designed in a similar way to a conventional velocity stack by routing the air more directly into your turbo charger and allows more air to be compressed due to its larger capacity, this can have a positive effect on acceleration after long deceleration or in between gear changes due to more air being kept within the intake system.Testing showed progressive gains throughout the rev range, below shows our worst and best dyno run with an exhaust and tuning box in place. On average gains of 4-5 bhp have been achieved with up to 10lbft of torque. These figures can vary depending on the tune calibration and various other modifications.FMTIA8 has been designed and developed to work with the OEM airbox as after testing many other options we found that the original airbox works extremely well especially when adding FMINLD1 our new carbon inlet duct to aid in keeping inlet air temps lower for longer while using on track.The turbo inlet adaptor and high flow inlet pipe has a capacity of more than 53% over the stock item. Not only will you notice the increased performance but a slight change in your engine acoustics can also be heard. As with all Forge Motorsport products we offer a no quibble lifetime guarantee on both the silicone hose and billet adaptor. A commonly asked question is will this fit with an aftermarket intake? the answer is yes it will fit other manufacturers intakes and fits to the original airbox.Manufactured from 6082 aerospace grade aluminium.CNC machined turbo adaptor, hose joiner’s and pipe bracketBlack anodised for ultimate protection and durability.Increased capacityNo engine check lights (EML)Increased air flowThese hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist.The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aestheticallyLifetime warrantyWarranty InformationThe majority of Forge Motorsport products come with a limited lifetime warranty (brakes pads excluded). All warranty claims must be accompanied by the original proof of purchase to enable us to help you. Failure to supply this proof will result in your claim or enquiry being denied.Do not use aggressive (acidic) car cleaning products, particularly traffic film remover solutions or shampoos to clean your intercooler, radiator, or oil cooler. The use of these products can damage Forge Motorsport cooling systems and invalidate your warranty. These are often found at car washes. A light, warm, soapy solution (free of harsh acidic cleaning compounds) should be used to clean you cooler and thoroughly rinsed away. We recommend that you should inspect your product on a regular basis for bent and/or crushed fins. Any bent fins should be carefully straightened to allow ambient air to pass through the core face. At the time of installing your Forge radiator, an approved coolant must be used and added to the coolant system. Be sure you never mix coolant and always use distilled water.This warranty does not apply to any defect in the goods arising from fair wear and tear, wilful damage, accident, negligence by you or any third party, use otherwise than as recommended by the supplier, failure to follow the supplier’s instructions, or any alteration or repair carried out without the supplier’s approval. THIS IS FOR STOCK TURBO FITMENT While we do our best to keep all items in stock, due to massive manufacturer issues in the industry sometimes there can be delays with some orders. If this is the case you will be contacted within 24 hours. Please contact us to check stock levels.
Price: 294 GBP
Location: Coventry
End Time: 2024-12-16T18:16:05.000Z
Shipping Cost: 43.03 GBP
Product Images
Item Specifics
Return postage will be paid by: Buyer
Returns Accepted: Returns Accepted
After receiving the item, your buyer should cancel the purchase within: 30 days
Return policy details: Our policy lasts 14 days from the date of delivery. If 14 days have gone by since your purchase, unfortunately we can’t offer you a refund or exchange. To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging and suitable for resale. Return postage costs are at the expense of the buyer and we recommend using a tracked and insured service. Inital delivery costs to the customer will also be deducted from the refund amount. Full refund policy can be found on our website - www.Wayside-Performance.co.uk
Warranty Period: LIFETIME
Other Part Number: NA
Classic Car Part: No
Mileage: NA
Manufacturer Part Number: FMTIA8
Grade: NEW
Reference OE/OEM Number: NA
Brand: Forge Motorsport
Interchange Part Number: NA
Unit Type: Unit
Vehicle Identification Number (VIN): NA
Unit Quantity: 3
Country/Region of Manufacture: United Kingdom
Performance Part: Yes
