DUST COLLECTOR , 5 HP, 4 CARTRIDGE

Description: Description CONSOLIDATED STRIPPING Visit my eBay Store:CONSOLIDATED STRIPPING BLASTING ABRASIVES | BLASTING EQUIPMENT | POWDERCOAT PAINTS | GLOVES | SHRINK WRAP STRETCH FILM This listing is for a new 2500 cfm @ 6.3" WC design resistance, 5 hp, automatic reverse pulse, dust collector system. This unit is currently oversold but will be in stock soon and available for shipment, pending payment and voltage information specific to your electical system requirements. Also available in single phase 230 volts for an additional charge of $495.00 USD. This listing information was last updated on October 16, 2023. It has 4 cartridges that reverse pulse clean via a programmable timer board and solenoid valve system. The cartridge dust collector is an excellent choice to replace the common bag-house or dust bag type collector and can be used to collect almost any dry, fine dust particulate. The cartridge offers a large amount of cleaning filter material in a very compact area. Cartridge dust collectors take up much less space than bag house collectors and offer an impressive filtration efficiency of 99.7% against 1/2 micron particles allowing for in house venting in applications that do not produce noxious or poisonous gases. It was designed with a 12 inch diameter, abrasive resistant, inlet to extend the filter life. The filters are cleaned with an automatically actuated reverse pulse of compressed air. The unit pictures assembled with stand are for display purposes only but is an accurate representation of unit as it looks installed using lift frame. This unit is currently equipped with our automated pulsing package. It is effective when used while the dust collector is in operation or shut down and can be used as desired to clean filters from accumulated particulate continuously or as required. The timer board is powered by standard 120v single phase electrical connection. It is factory programmed for 3 minute intervals, completely cycling all filters once every 6 minutes when energized. This unit is designed to deliver optimal performance when dust cake levels of 40-80-160 pounds or less are accumulated in between pulse cleaning intervals or it may remain energized for continuous filter cleaning. It is equipped with an accoustical dampening package that will comply with the maximum noise levels allowed per osha regulations. This unit uses an oversized impeller at a lower speed to further reduce noise levels. The vertical placement of filters allow for the best possible release and removal of dust from the pleated filters during pulse cleaning. Two (2) filters are cleaned at the same time on this unit. It has four (4), 99.7 % efficient cartridges that contain 912 square feet of total cleaning surface area. Each 26 inch long and 12.75 inch diameter filter cartridge has pleats that are 2.375 inches deep. The center opening of the filter is 8 inches in diameter and is open on one end before installation. Filters in this unit are a single stack set of four (4). They are one of the most popular filters made and can be replaced with any similar filter cartridge without regard to warranty restriction or voidance. Filters will require replacement generally once every 2-3 years on average. Some applications with high humidity, oily, fibrous, magnetic, or aglomeric particulates may reduce this substantially. Currently, it is offered with a 5 hp, (208v - 230v / 460v) 3 phase TEFC motor as standard equipment ( 18 - 16 / 8 amps ). The approx. dimension of this collector is 10 ft. high, 5 ft. wide and 5 ft. deep. It is pictured with a barrel kit for 55 gallon drum disposal. This dust collector is equiped with a 16.5 inch diameter straight radial impeller, inside an 8 inch high scroll housing as standard equipment and maximum rotational velocity of 2900 RPM. This unit has the following fan curve performance 2500 CFM @ 6.3" WC 2266 CFM @ 7.0" WC 1983 CFM @ 8.0" WC 1763 CFM @ 9.0" WC 1587 CFM @ 10.0" WC 1442 CFM @ 11.0" WC 1322 CFM @ 12.0" WC This unit is equipped with our VFD electrical package that includes the following: Soft motor starting: The amperage draw will not exceed the motor name plate rated amperes at any time. This reduces the initial cost of copper wiring because it is no longer necessary to consider the initial startup load. The initial startup requirements may exceed 5 times the rated name plate amperes when hard starting a variable torque application like high speed impellers. This requires over-sizing of electrical wiring, fuses and breakers to prevent motor starvation and premature failure of electrical components on startup.On-Off Switch: Conveniently located on the variable frequency drive and engaged with the push of a button. After the start command is triggered the motor will ramp to maximum velocity over ~ 30 seconds. When the stop command is received the unit will again decelerate over ~ 90 seconds and come to a complete stop.Thermal Motor Protection: The motor drive will constantly monitor the motor and the drive itself for any unusual spike in temperature throughout. If the temperature rises above acceptable parameters the drive will default and shutdown before any damage to the unit is sustained.Motor Fault and Report Monitoring: The motor drive is capable of displaying motor torque, hours of operation, actual amperage draw, percentage of motor capacity used, percentage of drive capacity used, the motor frequency in hertz, delivered line voltage and several other programmable LED display readouts. Factory settings are always in hertz frequency unless specified otherwise.Automatic Load Compensation Controls: The motor drive is programmed to compensate for changing load conditions. These conditions include, but are not limited to, extended length or reduced diameter of piping, blast gates and other restrictions in the air lines, atmospheric humidity, temperature and altitude, filter cartridge dust cake levels, and power supply brownout or overcurrent conditions. The LED display will show reading in real time with .1 hertz accuracy. This reading can also be used as a baseline to determine the most effective time to change the filters. For outdoor placement of the dust collector body, the VFD package must be located to inside the building. Our VFD electrical package is included on this unit. Contact us with any questions you may have about your specific applications. Our equipment comes with a 1 year warranty against defect in workmanship or materials. We also offer an 85% return of the purchase price, excluding freight, for the return of the collector within 90 days after receipt of delivery if this unit fails to perform as described.

Price: 7790 USD

Location: Plainwell, Michigan

End Time: 2024-08-17T22:59:55.000Z

Shipping Cost: N/A USD