BP :Single Shot: 100% Solids Epoxy Resin Kit CLEAR (3 Gallons) Garage/Floor Kit

Description: Single Shot | 100% Solids Epoxy Resin Kit (3 Gallons) - Solvent-Less, Two Component Epoxy Glossy Coating SystemCovers up to 300 SQFT. Perfect for Industrial Use, Garages, Floors and Much More!3 Gallon Kit covers up to 300 SQFT. Depending on Porosity and desired thickness.Dense surface resistant to contaminants and moisture and easy to clean.May apply several layers on itself with excellent adhesion.Contains no solvent with a very low VOC content (VOC = 75.4 g/L), allowing for interior application without harmful odors.Excellent adhesive properties, allowing application on other firm and hard coating, as well as a good bond to the substrateCures Clear with a beautiful finish mirror finish.Features & Cure TimeAvailable in Pre-Tinted ColorsWorking Time: 40 minutesPot Life 16 OZ (454 G) = 10-15 minutes @ 77°F (25°CFoot Traffic: 16-30 HoursLight Traffic: 2-5 DaysFull Cure: 5-10 DaysSurface Preparation - Old ConcreteConcrete surface must be cleaned. BLASTRAC, sand blasting, diamond grinder w/30 grit or coarse, or water blasting is highly recommended to remove surface contaminates. Any oils and fats must be removed prior to product application. Acid etching may be required (followed by a thorough rinsing) to open the pores of the concrete to accept a primer. Do not apply to wet substrates. Chloride, moisture, and pH levels should be checked prior to application. In almost every application a primer is recommended prior to use of SINGLE SHOT.Surface Preparation - New concreteThe concrete should be allowed to cure for a minimum of 30 days. Compression resistance of concrete must be at least 25 MPa (3625 lb/inch2) after 28 days and traction resistance must be at least 1,5 MPa (218 lb/in2). BLASTRAC, sand blasting, diamond grinder w/30 grit or coarser or acid etching (followed by a thorough rinsing) is required to remove the surface laitance that appeared during the curing process. A primer should be used to reduce out-gassing and promote adhesion.MixingMaterials should be pre-conditioned to a minimum of 50°F (10°C) prior to use. Thoroughly mix each component separately. Pour component B into component A using the proper mixing ratio of 2A:1B by volume. Mix both components for at least 1 minute using a drill at low revolution (300 to 450 rpm) to reduce trapping of air. While mixing, scrape bottom and walls of container at least once to ensure a homogeneous mix. Only prepare quantity that may be applied during pot life of mixture.ApplicationApply mixed product on the prepared surface tightly (thin film) using a rubber rake and pass a roller to obtain a uniform coating. Avoid creating puddlesPROPERTIES @ 73°F (23°C) AND 50% R.HHARDNESS (SHORE D), ASTM D224085-90RESISTANCE TO MOLD GROWTHRated 10 (highest resistance)ELONGATION (%), ASTM D6386.7FLAMMABILITYClass I (Not considered Flammable, Flash Point > 199.4ºF (93ºC)TENSILE STRENGTH (PSI), ASTM5500PERMEABILITY (%), ASTM D5700.3%BOND RESISTANCE (PSI), ASTM> 300 (substrate ruptures)MIX RATIOBY VOLUME: A:B = 2:1BY WEIGHT: Clear: A:B = 100:41-48 Colors: A:B = 100:39-45 With quartz sand : A:B = 100:50 Mixture = 200TECHNICAL DATARECOMMENDED THICKNESS: PrimerSOLID COLOR: @ 10 mils (150 ft²/gal)FLAKE SYSTEM: @ 10 mils (150 ft²/gal)METALLIC SYSTEM: @ 10 mils (150 ft²/gal)RECOMMENDED THICKNESS: Finish CoatSOLID COLOR: @ 16 mils (100 ft²/gal)FLAKE SYSTEM: @ 13 mils (120 ft²/gal)METALLIC SYSTEM: @ 40 mils (40 ft²/gal)epoxy resin for floors general use epoxy resin resin epoxy kit epoxy floors epoxy gallons epoxy resin gallons of resin garage solid epoxy resins epoxy resin flooring kit cheap epoxy resin kit epoxy resin floor kit epoxy resin 3 gallon kit epoxy resin

Price: 199.99 USD

Location: Fredericksburg, Virginia

End Time: 2024-08-16T16:23:11.000Z

Shipping Cost: 0 USD