Aluminum 2 Line Separator for 1 #12 & 1 #10 AN Lines Squeeg's LS2-112-110

Description: Line Separators: Black anodized aluminum line separators for Fuel Line & Oil Line. Separators for two, three or four lines available in all popular configurations. An innovative design where the lines simply clip in to make installation and future servicing a snap with no fiddly hardware to lose. Made from extruded T-6061 aluminum. Currently, there are 34 different configurations for Fuel and Oil lines. Also available for Heater A/C Line - including the new EZ-Clip AC Line. Matching Plug Wire Separators also available.1 line separator for 1) #12 & 1) #10 AN lines.Note: Line Separator listed size refers to the inner diameter of the line. Refer to this chart for the outer diameter of the line. Hose # Fraction Decimal #4 27/64" 0.422 #6 17/32" 0.531 #8 5/8" 0.625 #10 3/4" 0.750 #12 29/32" 0.906 All of our products are proudly 100% made in the U.S.A. Our products are original designs meant to fill a void in the market, not just a copy of something already being offered. We have been using these parts for years in the shop on the cars we drive and build at Squeeg’s Kustoms. Look for our other parts on our eBay store. Also available from Squeeg’s Hot Rod Connection A/C & Heater Line Separators: Squeeg’s offers a simple solution to clean A/C and Heater line routing! Since the lines simply clip into the separators it is easy to remove the lines without having to unbolt anything. Available for standard A/C and Heater lines as well as for E-Z Clip A/C Line. Made of extruded T-6061 aluminum and cut on a water jet. Offered in black anodized aluminum our line separators look great on any vehicle. Aluminum Ferrules: A unique alternative to simply using a rubber grommet when routing lines, cables, wires, etc. through any panel. Deep enough to run through frame rails or can be used on thin sheet metal panels. 5 sizes available from ¼” to 1 ¼”. Bulkheads: Currently 5 items consisting of an aluminum bolt-on brake line bulkhead and 4 steel weld-in frame bulkheads to run lines or wiring through your frame. Weld in bulkheads available with a plain removable plate or with two terminals perfect for running wiring from your battery to your starter. Squeeg’s offers its own design of bulkhead plates for use in any frame. Chose from a blank plate or with terminals. The weld-in plate consists of ¼ 1018 steel and is milled to accept a precision fitted cap. Offered in an oval or round design, these plates will allow you to run your plumbing or electrical through your frame rails. The electrical plate consists of two nylon insulated terminals with brass inserts. The small terminal is tapped at 10/32 and the large is at ¼ 20. This is ideal for running electrical to the starter. We also offer a blank plate which can be drilled for AN bulkhead fitting for plumbing or any other use you may need. Epoxy Primer Filler Kits and Epoxy Top Coat Kits: Looking for the good stuff you used to use? Our legendary Epoxy Primer is still available! The same stuff we’ve been using in the shop for decades is still available. As this product cannot be shipped to some areas please contact us for more information. Exhaust Tips: Beautiful brushed stainless steel exhaust tips flared at the ends designed to be welded on. Available for 2”, 2-1/2” & 3” exhaust. Pewter Key Chains: Based on original artwork by Jimmy Smith of cars built by Squeeg’s Kustoms. 6 designs available; 32 Ford Coupe, 33 Ford Roadster, 34 Ford Coupe, 36 Ford Coupe, 40 Ford Coupe, and 50 Merc Custom. Plug Wire Separators: Black anodized aluminum separators for plug wires. Just like our Line Separators, the wires simply clip in to make installation and future servicing a snap with no fiddly hardware to lose. Offered in 8mm and 8.5mm. There are 6 kits for Big Block Chevy, Small Block Chevy, and Small Block Ford. Also available are the individual components so customers can build their own kits. The wire mounts are sold two per pack and the floating separators four per kit. There are 14 different components available. Steering Wheels, Adapters & Spacer: Cast aluminum I Beam style perfect for early hot rods. Available smooth or drilled, as cast or polished, wrapped or unwrapped. 8 configurations currently offered. Two column adapters available: early Ford (1928-48) keyed columns and GM splined columns as well as an Aluminum ½” spacer. T-Shirts: 10 Styles available featuring artwork by Jimmy Smith. Each style is available in either Black or White in Sizes from Small through 3XL. Many clearance shirts are available in various colors as well as Women’s shirts. Wheels: Early Sprint Car style classic aluminum wheels. Available in Starburst for Ford spindle mount 15” x 4.5”, Sprint in sizes from 15” x 4.5” through 16” x 10”, and Champs in sizes from 16” x 11” through 16” x 13”. All wheels are made to order. Standard available bolt patterns 5 on 4 ½”, 5 on 4 ¾” and 5 on 5 ½”. Other bolt patterns are available, contact us for more information. Wheel Center Caps: Cast aluminum caps designed to match cast wheels. Originally designed for American Rebel wheels, but suitable for many other wheels. Made in flat or with a domed center. Available as cast or polished in 5 on 4 ½”, 5 on 4 ¾” and 5 on 5 ½” bolt patterns. PROP 65 WARNING: May contain materials known to the state of California to cause cancer or reproductive harm.

Price: 9.95 USD

Location: Chandler, Arizona

End Time: 2025-01-21T20:30:00.000Z

Shipping Cost: 8.55 USD