Description: 无标题文档 11001 Deluxe Pinion Depth Gauge Checker Tool Kit For GM Ford Chrysler Dana 30-80 11001 Differential Pinion Depth Checker Kit Fit For GM 10-14 Bolts, Ford 8” 8.8” 9”, Dana 30-80, Chrysler Replace for T&D 11001 Pinion Depth Checker NOTE: Each of the three included calibration tubes is calibrated and sealed for each application. Important: Please clean all parts carefully before attempting calibration. Any dirt will prevent proper calibration. Insert the dial indicator into the cross shaft, with the dial indicator on the rounded side of the shaft and the tip through the flat area on the other side. Tighten the set screw, making sure not to overtighten.R Remove the indicator extension stored in the appropriate calibration tube and screw the tip of the extension into the dial indicator until snug.H Hold the Cross Shaft and indicator assembly with the tip of the indicator facing up. Slide the calibration tube onto the tip and allow the tube to rest on the flat area of the cross shaft.T The thousandths (long arm) pointer should turn slightly clockwise, pointing roughly straight down, or to the 6 o'clock position. If the pointer is not straight down, loosen the set screw on the cross shaft and raise or lower the indicator until the pointer is straight down with the calibration tube is in place. Tighten the set screw until snug (overtightening can lock the indicator shaft or permanently bend the housing) and make sure the pointer stays straight down. NOTE: Make sure the short hand (sub-dial) is in the "zero" position. Loosen the indicator bezel locking screw and with the calibration tube in place, make final adjustment by rotating the dial face until the zero position is aligned with the pointer. Tighten the indicator bezel locking screw. Your Pinion Depth Checker is now set and calibrated for a depth of exactly3.375 inch (Or 1.900 inches for Ford 9” and 2.500 inches for center differentials). This is the calibration depth. MEASURING PINION DEPTH 1、 Carefully remove any sharp edges or burrs from the carrier bearing housing and cap to avoid inaccurate or damaged hubs. 2、 Make a note of the pinion depth on the pinion gear. If your pinion does not have a depth number on it, go to the “OEM Gear Applications” Section to find the pinion depth. 3、 Put the pinion in the case with the appropriate bearings and spacers. 4、 Clean the surface of the appropriate target plate and pinion gear, then place the Target Plate on the surface of the pinion. 5、 Select a suitable hubs and lightly oil the bores to prevent galling and carefully insert the Cross Shaft into the hubs. Place this assembly into the enclosure and tighten the main cap bolts to 25 ft.-lbs. See the hub application. NOTE: The "A" diameter has a machined flat to clear the pinion support in the Ford 9" rear end. Individual applications may require additional relief. When using the "A" diameter in Dana 60s, the machined flat should be located at 90 degrees to the cap parting line. 6、 Slide the indicator and cross as close as possible to the pinion gear to minimize any overhang of the target plate. Make sure to retract the indicator plunger shaft just enough to clear the target plate to prevent the indicator from bending. 7、 Be sure the Indicator shaft end is on the target plate and note the reading on the dial. Multiply the small counter number by 0.100" and add the thousandths pointer reading to get your INDICATOR READING. Subtract your INDICATOR READING from the CALIBRATED DEPTH (3.375 for the long calibration tube, 2.500 for the intermediate,1.900 for the short), you will have the measured pinion depth. Example: If the reading on the indicator were 0.778" (seven full revolutions plus the reading), subtracting from 3.375 would equal 2.597". This is the measured pinion depth. Note: In order to minimize the error，rotate the pinion gear to at least four different positions and average the three most similar readings. 8、 Compare the MEASURED PINION DEPTH to the Pinion Depth number inscribed on the pinion gear or obtained from the OEM Gear Section to determine the amount of shims to be added or removed. Ford Front Crank Wear Sleeve Installer Kit Fit for Powerstroke 6.0L 2003-2010 66.96 USD OTC522 Large Gear and Pulley Puller Replace Fits Ford D80L-522-A and 303-D025 49.47 USD Oil Supply Rail End Plug Set 4C3Z-6026-CA for 1994-2003 7.3L Ford Powerstroke 34.99 USD Crankshaft Front Seal Installer Alt 303-1259 ZTSE4691 Fits Ford 6.4L F-250-550 73.48 USD Oil Rail Ball Nipple Cup Impact Tool & O-Rings Seal Kit for Ford 6.0L Diesel 42.99 USD Oil Rail Ball Tube O-Rings Repair Kit+Injector Seal Kit For 2003-2007 Ford 6.0L 79.99 USD 6.0 High Pressure Oil Pump IPR Valve Air Test Fitting Tool Fits Ford 6.0L Engine 12.48 USD IPR Valve Air Test Fitting Tool & Regulator Valve Removal Tool Fit for Ford 6.0L 28.96 USD Inner Axle Seal Installer Fits for Ford Super Duty Dana 50 /60 Axle 66.48 USD 3418 Fuel Injector Removal Tool Fit for 6.7L Ford Powerstroke 2011-2018 F250-550 44.48 USD 17mm 12pt Socket Injector Line Removal Tool Sl11400 Fits Ford Power Stroke 6.7L 39.48 USD Fuel Injector Socket Set&Injector Removal Tool Fits 6.7L Ford 2011-2018 F250-550 83.48 USD Fuel Filter Return Line Connector Fitting Fit Ford 2017-2020 Powerstroke 6.7L 29.47 USD Transmissions Tool Lip Seal Installer Protector Kit Fit Ford AOD AODE 4R70W 4R75 79.96 USD Power Stroke Front Crankshaft Seal Installer Tool Fits Ford F250-750 Alt ST-137B 319.48 USD Injector Sleeve Cup/Seat/Bore Cleaning Brush Kit Fit Ford /Caterpillar/ Navistar 20.48 USD W302193 Rocker Arm Retainer Clip Fit for Ford F250 F350 F450 F550 2003-2010 6.0L 29.48 USD Fuel Pressure Test Fitting Adapter Fit 6.0L Ford Diesel Engine 2003-2010 15.97 USD Camshaft Cam Pulley Sprocket Holder Tool For Ford, Dodge, GM, Honda, Mazda,Volvo 32.97 USD Water Pump Pulley Removal Tool 303-S455 211-185 303-009 Fits for Ford/Mercury 197.99 USD Differential Cover Gasket Rubber Coated Steel Core fit for Ford 8.8 Axles F880 17.57 USD Fuel Injector Holding Fixture Tool Fit Ford 2003-2010 6.0L Engines VT365/ VT275 36.63 USD 303-1514 6.7L Rear Crankshaft Seal Installer Tool for Ford F-250/350 /450/550 369.95 USD 4.4123R Energy Suspension Body Mount Bushing Kit Fits Ford F150 F250 F350 Truck 159.85 USD Polyurethane Body Mount Bushing Set Kit Fit for Ford F150-350 1980-1998 2WD 4WD 124.96 USD 6695 Wheel Knuckle Vacuum Oil Seal Installer Fits Ford 1998-2004 F-250-550 68.97 USD 303-1513 Rear Crankshaft Seal Installer Alt ST-148 Fit for Ford 6.7L Powerstroke 269.96 USD 11001 Deluxe Pinion Depth Gauge Checker Tool Kit For GM Ford Chrysler Dana 30-80 459.99 USD ST-152 6.7L Front Crankshaft Seal Remover Tool 303-1510 Fits Ford Super F250-750 188.48 USD TU-15-24 Diesel Compression Test Adapter M14-1.25 Fit Ford/Navistar 6.0L & 6.4L 39.96 USD Fuel Injector Return Line T Fitting Brass Fuel Line Hose Tee Connector Fits Ford 16.83 USD Diesel Fuel Banjo Bolt & Washer Kit Ultra High Flow Upgrade Fit Ford 6.0L & 6.4L 24.48 USD 600-249 Locking Hub Service Kit Fits for Ford F250 F350 F450 F550 2005-2018 14.96 USD Mechanical Fuel Pump Eccentric Kit For SBF Ford 302 289 351W 5.0 BBF 429 385 460 18.96 USD 6697 Wheel Oil Seal Installer Axle Tool Fit Ford 2005 to Current F-250 F-350 76.99 USD Fuel Injector Sleeve/Cup Puller & Installer Tool Fit Ford Powerstroke 6.0L&6.4L 98.99 USD Double Clutch Dry DPS6 Transmission Installer Remover Tool 307675 For Ford Volvo 176.99 USD Timing Chain Locking Wedge Holding Tool Fit Ford Mustang Lincoln Mercury F-150 11.56 USD FOR 2003-2007 Ford 6.0L Diesel Nipple Cup Socket Repair Kit with O-Rings Socket 33.99 USD Dry Type Dual Clutch Transmission Oil Seal Removal Tool for Ford Focus Fiesta 98.99 USD Dry Type Dual Clutch Transmission Oil Seal Removal Tool for Ford Focus Fiesta 98.99 USD Cylinder Head Repair Kit Fit Ford 6.0L Powerstroke Engine Fuel Injector Sleeve 132.99 USD Cylinder Head Repair Kit&Fuel Injector Sleeve Tool Fit Ford 6.0/6.4L Powerstroke 245.50 USD KF04050BK Polyurethane Body Mount Bushing Kit for 1999-17 Ford F250 F350 2WD 4WD 56.40 USD KF04050BK Body Mount Bushing Kit for 1999-2017 Ford F250/350 2/4WD Polyurethane 68.97 USD Dry Type Dual Clutch Transmission Oil Seal Removal Tool for Ford Focus Fiesta 98.99 USD HPOP High Pressure Oil Pump Master Service Kit for 1994-2003 Ford 7.3L Navistar 49.07 USD 74mm 14 Flute Oil Filter Cap Wrench Socket Remover Tool for Dodge Ford Toyota 12.97 USD 303-770 Crankshaft Rear Main Seal & Wear Ring Installer for Ford 4.5L/6.0L/6.4L 98.99 USD 0033 Universal Transmission Front Pump Remover Tool Replace for GM Ford Chrysler 92.99 USD 0033 Heavy Duty Transmission Front Pump Removal Tool Set For GM Ford Chrysler 89.97 USD 303-1248 303-1530 Camshaft Holding Tool Set Fit Ford Mercury 4V Engines 3.5/3.7L 29.99 USD 7834 Rear Crankshaft Seal Installer For Ford Aerostar 93-97 & Ranger Explorer 37.99 USD Automotive Cam Timing Alignment Tools Kit Fit for Ford Fiesta Focus Volvo Mazda 17.97 USD Crank Pulley Bolt Crankshaft Tool for Ford Lincoln Mercury Vehicles F5RZ-6A340-B 8.47 USD High Pressure Fuel Rail Adapters Pressure Oil Rail Leak Test Kit Fit Ford 6.0L 14.96 USD Air Test Fitting Tool &Oil Rail Adapter Leak Test Kit Fit Ford 6.0L Powerstroke 18.46 USD High Pressure Oil Pump IPR Valve Air Test Fitting Tool Fit Ford Powerstroke 6.0L 28.86 USD Cam Phaser Delete Lockout Aluminum Block Fit Ford 4.6L 5.4L 6.8L 3V F250-350-450 16.48 USD 2 PcsTiming Chain Wedge Fixing Tool+ Ford Cam Phaser Locking Kit for Engine 20.97 USD 6599 Fuel Tank Lock Ring Wrench Tool Pump Removal Installer For GM Chrsyler Ford 30.53 USD RK-25 Repair Kit for Model 25 wall Faucet Repair Kit Fit for Woodford Freezeless 40.99 USD For 98-04 Ford F250 F350 Excursion Thrust Washer Snap Ring Kit 50 60 Super Duty 12.99 USD 9N12104 Distributor Gasket Set,Compatible with Ford/New Holland Tractor 2N 8N 9N 9.75 USD Axle Knuckle Tube Dust Seal Snap Ring Kit for Ford Super Duty Excursion F250-550 199.98 USD 77110 Harmonic Balancer Socket 22mm Crank Bolt Socket Fits for Ford Jeep Toyota 29.99 USD High Pressure Oil System IPR AIR TEST Tool Fit for Ford 6.0L & 7.3L Powerstroke 169.99 USD Fuel Filter Tank Supply Line Connector Kit Fit Ford 6.7L Powerstroke 2011-2022 45.99 USD Silicone Body Mount Bushing Kit Fit 08-16 Ford Super Duty F-250 F-350 Crew Cab 349.99 USD Diesel Fuel Injection Line Clamp Set Fits 1983-1994 Ford 6.9L / 7.3L IDI Engine 39.99 USD 11001 Differential Pinion Depth Checker Kit Fit For GM 10-14 Bolts, Ford 8” 8.8” 9”, Dana 30-80, Chrysler Replace for T&D 11001 Pinion Depth Checker NOTE: Each of the three included calibration tubes is calibrated and sealed for each application. Important: Please clean all parts carefully before attempting calibration. Any dirt will prevent proper calibration. Insert the dial indicator into the cross shaft, with the dial indicator on the rounded side of the shaft and the tip through the flat area on the other side. Tighten the set screw, making sure not to overtighten.R Remove the indicator extension stored in the appropriate calibration tube and screw the tip of the extension into the dial indicator until snug.H Hold the Cross Shaft and indicator assembly with the tip of the indicator facing up. Slide the calibration tube onto the tip and allow the tube to rest on the flat area of the cross shaft.T The thousandths (long arm) pointer should turn slightly clockwise, pointing roughly straight down, or to the 6 o'clock position. If the pointer is not straight down, loosen the set screw on the cross shaft and raise or lower the indicator until the pointer is straight down with the calibration tube is in place. Tighten the set screw until snug (overtightening can lock the indicator shaft or permanently bend the housing) and make sure the pointer stays straight down. NOTE: Make sure the short hand (sub-dial) is in the "zero" position. Loosen the indicator bezel locking screw and with the calibration tube in place, make final adjustment by rotating the dial face until the zero position is aligned with the pointer. Tighten the indicator bezel locking screw. Your Pinion Depth Checker is now set and calibrated for a depth of exactly3.375 inch (Or 1.900 inches for Ford 9” and 2.500 inches for center differentials). This is the calibration depth. MEASURING PINION DEPTH 1、 Carefully remove any sharp edges or burrs from the carrier bearing housing and cap to avoid inaccurate or damaged hubs. 2、 Make a note of the pinion depth on the pinion gear. If your pinion does not have a depth number on it, go to the “OEM Gear Applications” Section to find the pinion depth. 3、 Put the pinion in the case with the appropriate bearings and spacers. 4、 Clean the surface of the appropriate target plate and pinion gear, then place the Target Plate on the surface of the pinion. 5、 Select a suitable hubs and lightly oil the bores to prevent galling and carefully insert the Cross Shaft into the hubs. Place this assembly into the enclosure and tighten the main cap bolts to 25 ft.-lbs. See the hub application. NOTE: The "A" diameter has a machined flat to clear the pinion support in the Ford 9" rear end. Individual applications may require additional relief. When using the "A" diameter in Dana 60s, the machined flat should be located at 90 degrees to the cap parting line. 6、 Slide the indicator and cross as close as possible to the pinion gear to minimize any overhang of the target plate. Make sure to retract the indicator plunger shaft just enough to clear the target plate to prevent the indicator from bending. 7、 Be sure the Indicator shaft end is on the target plate and note the reading on the dial. Multiply the small counter number by 0.100" and add the thousandths pointer reading to get your INDICATOR READING. Subtract your INDICATOR READING from the CALIBRATED DEPTH (3.375 for the long calibration tube, 2.500 for the intermediate,1.900 for the short), you will have the measured pinion depth. Example: If the reading on the indicator were 0.778" (seven full revolutions plus the reading), subtracting from 3.375 would equal 2.597". This is the measured pinion depth. Note: In order to minimize the error，rotate the pinion gear to at least four different positions and average the three most similar readings. 8、 Compare the MEASURED PINION DEPTH to the Pinion Depth number inscribed on the pinion gear or obtained from the OEM Gear Section to determine the amount of shims to be added or removed.
Price: 473.5 USD
Location: Walton, Kentucky
End Time: 2024-10-25T10:57:29.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: JIAD
Manufacturer Part Number: 11001
Type: Deluxe Pinion Depth Gauge Checker Tools
Warranty: 1 Year
Fitment 1: For GM 10 bolt 12 bolt, Dana 30-70, Ford 8.0'', 8.8'', 9.0''
Color: Silver
Material: 4140 Impact Grade Steel
Fitment 2: For Ford 8” 8.8” 9”, Dana 30-80, Chrysler
OE/OEM Part Number: 11001
Set or Single Item: Set
